- 抗彎模數
- 彎曲彈性模量
- 彎曲模量
- 彎曲模數
- 彎曲系數
下載手機詞典可隨時隨地查詞查翻譯
bending modulus中文什么意思
例句與用法
- Standard test method for apparent bending modulus of plastics by means of a cantilever beam
用懸臂梁法對塑料表觀彎曲系數的標準試驗方法 - Results showed that , clay was only dispersed in the epoxy phase and had not any effect on the phase separation of epoxy and ctbn . with the increase of clay concentration , the impact strength of composites decreased significantly while the bending modulus increased
結果表明，使用熔融插層法只能制備出粘土完全分散在ep相的三元復合浙江大學碩士論文材料，粘土的加入對橡膠和環氧樹脂的相分離過程影響不大。 - The result showed when common montmorillonite , in which the mass fraction of montmorillonite was 75 % , was used as modifier , the bending modulus of the compound increased by more than 60 % , impact strength increased by a factor of 2 , recovery ratio reduced 35 % , and the compound had good processability
結果表明，在采用蒙脫石質量分?jǐn)?shù)為75 %的普通蒙脫土?xí)r，專用料彎曲模量提高60 %以上，沖擊強度提高一倍，回縮率降低35 % ，并且加工性能良好。 - The results show that fsmf can improve the bend modulus of the resin cast clearly , but reduce the tensile strength . in the suitable content of filler ( not more than 30 % in this experiment ) , fsmf can improve the tensile modulus and bend strength . in the suitable content of filler ( 20 % ~ 30 % in this experiment ) , fsmf can improve the toughness of the resin cast
結果表明： fsmf顯著提高樹脂澆鑄體的彎曲模量，但降低拉伸強度；在合適的填料含量(本實驗中為30 )下， fsmf可提高樹脂澆鑄體的拉抻模量和彎曲強度；在合適的填料含量(本實驗中為20 30 )下， fsmf可起到增韌效果，改善樹脂澆鑄體的斷裂韌性。 - The results of the experiment are as follows : the bend strength , bend modulus , stiffness and toughness of the mortar layer will be improved when add 30 % fsmf to resin . the axis tensile strength , stiffness , hardness and weariessness of winding layer will be improved when add 25 % ~ 30 % fsmf to resin
提出了應用設想并進行了實驗研究，結果表明:在樹脂中加入30 %的fsmf ，可提高夾砂層的彎曲強度、彎曲模量、剛度和韌性;在樹脂中加入25吠尸30 %的fsmf ，可提高纏繞層的軸向拉伸強度、剛度、硬度和耐磨性，降低成本。